No.

Description

100

Error: There is an open circuit in the antenna power/data cable. Check the cable.

101

Error: There is a short circuit in the antenna power/data cable. Check the cable.

102

Warning: The ICM is not providing the proper DC power to the antenna. Check the wires on the back of the ICM.

103

Warning: A software update file was not found on the USB device. Try these steps:

•Remove the USB device from the ICM, wait 10 seconds, then reinsert it.

•Verify that a valid TracPhone V7-IP update file (ending in “.kvh”) is present on the USB device in its root directory.

•Replace the update file on the USB device with a new file.

•Use a different USB device.

104

Warning: The software update file you selected is corrupt. Try a new update file.

105

Warning: The ICM is unable to read from or write to its internal memory (EEPROM). Contact KVH.

106

Error: The ICM has lost communications with the antenna. Try these steps:

•Check the wiring on the back of the ICM.

•Check the antenna power/data cable.

•Try turning the system off, then back on.

107

Warning: The ICM’s internal temperature exceeds acceptable limits. Try these steps:

•Listen for the cooling fan inside the ICM. If you don’t hear the fan, contact KVH.

•If you hear the cooling fan, turn off the system and allow it to cool down. Then vacuum the ICM’s vents (see Preventative Maintenance).

•If the problem persists, you might need to relocate the unit to an area that provides better ventilation.

111

Warning: The ICM is unable to initialize its built-in wireless access point (WAP). Contact KVH.

112

Warning: There is an internal fault in the ICM. Contact KVH.

117

Error: There is an open circuit in the BUC power cable (ICM jumper cable between C1 and C2) or the transmit (TX) RF cable. Check the cables. If the cables are OK, the BUC might be faulty – contact KVH.

118

Error: There is a short circuit in the BUC power cable (ICM jumper cable between C1 and C2) or the transmit (TX) RF cable. Check the cables. If the cables are OK, the BUC might be faulty – contact KVH.

120

Warning: The internal temperature of the ICM’s built-in modem exceeds acceptable limits. Try these steps:

•Listen for the cooling fan inside the ICM. If you don’t hear the fan, contact KVH.

•If you hear the cooling fan, turn off the system and allow it to cool down. Then vacuum the ICM’s vents (see Preventative Maintenance).

•If the problem persists, you might need to relocate the unit to an area that provides better ventilation.

121

Error: The ICM is not receiving satellite signal strength (RSSI) data from its built-in modem. Try these steps:

•Turn the ICM off, then back on.

•Check the serial data jumper cable on the back of the ICM connecting between A1 and A2.

122

Error: The ICM’s built-in modem is not communicating. Try these steps:

•Check the ICM jumper cables.

•Try turning the ICM off, then back on.

•If the error persists, contact KVH.

123

Error: The ICM’s built-in modem is not responding to status queries. Contact KVH.

124

Warning: The software update file you selected is not valid for the TracPhone V7-IP. Try a new update file.

125

Warning: The ICM has lost communications with the GPRS modem (remote service & support module) inside the antenna. Check the power/data cable and the wires on the back of the ICM.

127

Error: The antenna is not accepting the no-transmit zones setup from the ICM. Contact KVH.

128

Warning: The software update failed. Retry updating the software. If it fails again, check the power/data cable and the wires on the back of the ICM.

130

Error: The ICM is incompatible with the antenna’s LNB. Either the ICM or the LNB is configured for HTS, while the other is not. Contact KVH.

131

Error: The antenna is running a version of software that does not work properly with the ICM. Update the software.

200

Warning: The antenna is not receiving adequate DC power from the ICM. Check the power/data cable and the wires on the back of the ICM.

204

Error: The antenna’s main board has lost RF communications. Try updating the software (see Software Updates).

206

Error: The antenna’s azimuth motor or limit switch failed. Contact KVH.

208

Error: The antenna’s elevation motor or limit switch failed. Contact KVH.

216

Error: The antenna’s cross-azimuth motor or limit switch failed. Contact KVH.

218

Error: The antenna’s skew motor or limit switch failed. Contact KVH.

219

Error: One of the antenna’s gyros is out of calibration. Try recalibrating the gyros (see Gyro Calibration). If a gyro fails to calibrate, contact KVH.

220

Warning: One of the antenna’s gyros failed. Contact KVH.

221

Error: The system is not receiving any GPS data. Contact KVH.

222

Warning: The antenna’s internal temperature exceeds acceptable limits. Turn off the system and allow it to cool. If the problem persists, contact KVH.

234

Error: The antenna is not receiving satellite signal strength (RSSI) data from the ICM. Try these steps:

•Turn the ICM off, then back on.

•Check the wires on the back of the ICM.

•Check the power/data cable.

235

Error: The antenna has lost RF communications. Contact KVH.

240

Error: The antenna’s LNB is not receiving the proper power from the ICM’s receive (RX) RF cable. Check the RX RF cable.

241

Error: The antenna’s main board detects a power failure. Contact KVH.

265

Warning: The GPS is unable to acquire a fix. Check for blockage or RF interference around the antenna.

269

Error: The antenna cannot determine which type of LNB is installed. Either the LNB type was not programmed at the factory, or the antenna’s memory (EEPROM) has been cleared or corrupted. Contact KVH.

270

Error: The ICM is running a version of software that does not work properly with the antenna. Update the software.

401

Warning: No NMEA 0183 heading input detected. Check the NMEA 0183 talker and its wires connected to the back of the ICM.

404

Warning: Antenna is unwrapping its coiled internal cable. Normal operation should resume within one minute.

410

Warning: The ICM has lost Ethernet communications with its built-in modem. Check the jumper cable connecting “B1” to “B2” on the back of the ICM.

411

Warning: The antenna cannot find an available service satellite. You are located outside the coverage area.

412

Warning: The ICM is not receiving the proper DC voltage from its power supply. Check the power cable

413

Warning: The antenna is waiting for GPS to acquire a fix.

414

Warning: The antenna is using position data from a backup GPS device and not its built-in GPS.

417

Warning: The antenna is pointing in a tracking avoidance zone. Performance might be degraded until the antenna can switch to an alternate satellite or move outside the zone.