Static IP HTS Configuration

In a Static IP HTS configuration, Ethernet port 1 provides unlimited Internet access with no user logins or controls. Ports 2 and 3 and the built-in WAP require a user login and provide high-speed Internet access. Port 4 is reserved for an optional KVH service, such as Global Static IP.

Important!

You should only assign a static IP address to a secure device, such as a firewall router.

A static IP connection is commonly used by commercial vessels to enable remote monitoring and IT management from shore, and to allow a vessel’s crew to access their company’s secure VPN (virtual private network).

Common Static IP Applications

V7HTS_static_IP_concept_ICM.png 

To set up the network in a static IP configuration, follow these steps:

  1. Make sure the system is activated for mini-VSAT Broadband service.

  2. Turn on the TracPhone system and make sure it is “Online.” The system must remain online to allow KVH to set up your system over the satellite link.

  3. Fill out the online form at www.kvh.com/staticip. Be sure to read all of the details on this form. An additional monthly fee for static IP service will apply.

    Important!

    Only the “User Ethernet 4” port on the ICM can be used to connect static IP devices, as this port bypasses the ICM’s local subnet to connect directly to the built-in modem.

  4. Connect your network device or computer to the “User Ethernet 4” port on the rear panel of the ICM. Use a straight-through CAT5 (or better) Ethernet cable with RJ45 connectors.

    5. Static IP HTS Configuration Wiring Example

    V7HTS_ICM_StaticIPHTS_config_example_color.png 

  5. At the TracPhone V7-HTS web interface or mini-VSAT Manager, select the Static IP HTS network configuration. Refer to Selecting a Network Configuration for details.

    6. Static IP HTS Configuration

    HTS_netconfig_StaticIP_Config_withborder.png 

  6. When you receive an email from KVH confirming that your static IP address has been set up, configure the TCP/IP properties of your network device or computer with the static IP data provided in the email. For details on accessing your computer’s TCP/IP properties, refer to Configuring Computers for DHCP.

    7. Static IP HTS Data

    Static_IP_setup_Win7_updated.png 

  7. Connect all other (non-static IP) computers and/or network devices to “User Ethernet” ports 1-3 on the rear panel of the ICM. Make sure you connect to the port(s) that correspond to the desired Internet connection path(s): Unlimited or High-speed. For example, you might wish to add an external WAP (or Wi-Fi router configured for bridge mode) to supplement Wi-Fi access. Use straight-through 100 Mbps fast Ethernet UTP CAT5 cables (or better) with RJ45 connectors.

  8. To enable the ICM’s built-in wireless access point (WAP) for Wi-Fi access, follow the steps in Wireless Settings.

  9. Make sure all non-static IP computers are configured for DHCP addressing (see Configuring Computers for DHCP). Devices connected to “User Ethernet” ports 1-3 and Wi-Fi will receive IP addresses from the ICM via DHCP. The ICM serves as a router.

  10. Set up user names and passwords and allocate data for each High-speed LAN user at the mini-VSAT Manager (www.mykvh.com). Go to the Terminal > Data Plan section of the Vessel Details page and select Data Allocation.

Data Allocation: Users (Example)

myKVH_CrewDataAllocation_UsersTab_crop00001.png 

Data Allocation: Allocation Profiles (Example)

myKVH_CrewDataAllocation_ProfilesTab_crop00002.png 

NOTE: By default, the High-speed LAN has a gateway of 192.168.6.1 and assigns IP addresses in the 192.168.6.50-150 range. If this configuration conflicts with an existing onboard network, you may change the settings at the TracPhone V7-HTS web interface (go to Settings > Network Settings). See LAN Settings for details. The Unlimited LAN (gateway 192.168.5.1) cannot be changed at the web interface. If it conflicts with an existing network, please contact KVH Technical Support for assistance.